novakerop.blogg.se - Seadoo vts bypass

SEADOO VTS BYPASS UPGRADE
SEADOO VTS BYPASS CODE
SEADOO VTS BYPASS PLUS
SEADOO VTS BYPASS FREE

Press MODE to scroll codes if more than one is present.

With safety lanyard on its post, press 5 times the SET button to start the display of P-codes (onboard diagnostic).

The procedure for retrieving codes is as follows: This will also record that the problem has been fixed in the MPEM/EMS ECU memory.Īlso note that if you get many fault codes at the same time, that may be due to a burnt fuse or fuses. This will properly reset the appropriate counter(s). If so, you should retrieve all the fault codes to try and figure out where the problem is located.Īfter a problem has been solved, ensure to have your local dealer clear the fault(s) in the MPEM/EMS ECU using his BUDS system since the fault codes registered in the MPEM (EMS ECU) are kept even when the battery is disconnected. If you’re having problems with your 4-TEC powered ski, first check if there is a message (Fault Code) displayed by the vehicle information center. The area above is always changing so check back often as links are added. Hopefully this page will help others avoid the same fate!ĬOMING SOON… Module Conversion Kits for 204470139 204470155 204470179 204470184 MPEMs Have you had a bad experience with a dealer, repair shop, or engine rebuilder? If so, now you can post your experiences here. If you have one, contact me with description and price. If you have parts or know of a Sea Doo dealer in your area that is closing, contact me at with the details.īlown or wrecked Sea Doo watercraft in the Ohio vicinity. Parts Inventories from overstocked or closing Sea Doo shops.

SEADOO VTS BYPASS PLUS

It would still be nice to find a relay with a current sense, then it would be an as stock fix.Sea Doo 4-TEC 4 Stroke Fault Codes Reference My friends at have many hard to find parts in stock as well as custom kits for your Sea Doo plus they ship all over the world so check them out for your Sea Doo parts needs! Overall I think this is a usable solution without having to spend $200 for a part that will eventually fail again, I paid $15 for all of the parts required. I plan on removing the 7.5A fuse when someone other than me is riding the ski to prevent problems. Find Seadoo Vts in Boats & Watercraft Boats for sale Find a local canoe, kayak, motorboat, seadoo, or other watercraft in Canada on Kijiji, Canadas 1 Local Classifieds. This relay does not have a current sense shutoff so if you hold the vts button(s) past the end of the motor travel you run the risk of damaging the mechanical gear and/or the motor so use with caution. I also recommend replacing the 15A fuse that comes with the relay with a 7.5A fuse for safety - this should not be an issue unless your motor is going bad and drawing too much current (if so you should replace the motor anyway). The small red wire from the relay that is the hot for the switch control is really light gauge wire so I chose to put a 3A inline fuse in just in case there is ever a short in the system. If you wanted to use the factory power pigtail from the coil box I think everything would still work fine and would be dead without the key. SeaDoo MPEM conversion kits for sale, converting is easier than a new MPEM.

SEADOO VTS BYPASS UPGRADE

I chose not to use the power wiring from the coil box as I wanted to isolate the vts system completely so if I ever had to do any electrical troubleshooting the vts wouldn't be a factor - the only flaw with this is the vts is hot without the dess key in. DESS & Other Switches Driveline Seal Assemblies SeaDoo Tool Rental VTS Boot Upgrade Kit Anti-Rattle Kits For Older Doos SeaDoo MPEM testing, repair and new sales with Dess key programming for ANY Seadoo MPEM, ECU, LCD, ECM, VCM. To my knowledge all of these dei relays are the same.

SEADOO VTS BYPASS CODE

Other skis should be very similar in color code if not identical. This is how I hooked mine up and it works.

SEADOO VTS BYPASS FREE

I attached a wiring diagram for a 96XP that I hope is pretty easy to read, feel free to let me know if anyone sees a flaw. Like koerbs said, when the work is done a picture really won't help, I put everything in heat shrink so you can't see anything. Well, I promised to do this so here goes.